0         1         2
        0.........0.........0
     00
     01      Programming
     02
     03  A: Road Config     >
     04  B: Velocity Config >
     05  C: Motor/Drive Cfg >
     06  D: Controller Cfg  >
     07                       <-- Room for 1 or 2 more menus if needed
     08  
     09  Ctl Ver: xx.yy.zzz   <-- Controller firmware version no.
     10  T/T Ver: xx.yy.zzz   <-- Receiver firmware version number
     11  IP: xxx.xxx.xxx.xxx  <-- If connected to the user's WiFi network
     12  
     13 PRG: Exit programming


        0         1         2
        0.........0.........0
     00
     01  Road Configuration
     02
     03  
     04  
     05  A: Add New Road    >
     06  B: Modify Road     >
     07  C: Delete Road     >
     08  
     09  
     10  
     11  
     12  PRG: Previous Menu    <-- Not happy with this, got any ideas?
     13 


        0         1         2
        0.........0.........0
     00
     01      Add New Road
     02
     03   Number:    XX         <-- Display number double-height
     04
     05
     06  0-9: Change Road
     07  <- : Rotate TT A/CW
     08  -> : Rotate TT CW
     09   * : Default  NO      <-- Display YES in reversed text if default
     10   # : Polarity NORMAL  <-- Display INVERT in reversed text if polarity is reversed
     11
     12   D : Save changes
     13  PRG: Previous Menu

        0         1         2
        0.........0.........0
     00
     01      Delete Road
     02
     03   Number:    XX         <-- Display number double-height
     04
     05
     06  0-9: Choose Road
     07  
     08   D : Delete road
     09  
     10  Press "D" again to     <-- Message appears after "D"
     11   confirm deletion      <-- is pressed for the first time
     12   
     13  PRG: Previous Menu


        0         1         2
        0.........0.........0
     00
     01    Velocity Config
     02
     03  1 rev = xxxxx steps
     04
     05  Normal Speed: xxxxx 
     06  Rapid Speed:  xxxxx
     07  Acceleration:  xxxx
     08 
     09  * / #: Prev / Next
     10  <- ->: Adjust value
     11  0-9  : Set value
     12    D  : Save changes
     13   PRG : Previous Menu

        0         1         2
        0.........0.........0
     00
     01  Motor/Drive Config
     02
     03  1 rev = xxxxx steps
     04
     05  A: Calibrate >
     06  B: Direction NORMAL  <-- Toggles to REVERSE
     07  
     08  Press "A" again to   <-- Message appears after "A" is
     09  start calibration    <-- pressed as a confirmation.
     10  
     11  D: Save & restart    <-- Appears if Direction is toggled
     12  
     13  PRG: Previous Menu

        0         1         2
        0.........0.........0
     00
     01   Controller Config
     02
     03  A: Rotate Display  >  <-- Essentially the same as current rotate screen
     04  B: Turntable Lock  >
     05  C: Alter Turntable >
     06  
     07  
     08  
     09  
     10  
     11  
     12  PRG: Previous Menu
     13 

        0         1         2
        0.........0.........0
     00
     01   Turntable Lock
     02
     03  A: Lock INTERNAL       <-- Cycle between DISABLED, INTERNAL, EXTERNAL
     04  
     05  Delay: XXXX mS
     06  
     07  <- ->: Alter Delay
     08  0-9:   Enter Delay
     09  
     10  B: HIGH is locked      <-- Switch between HIGH and LOW output
     11  
     12  D: Save Changes
     13  PRG: Previous Menu

        0         1         2
        0.........0.........0
     00
     01   Alter Turntable
     02
     03  <-: Move T/T up
     04  ->: Move T/T down
     05  
     06  
     07  
     08  
     09  # : Forget this T/T
     10  
     11  D : Save changes
     12  PRG: Previous Menu
     13